Assess & quote
Site visit, plan review and Dial Before You Dig. One clear quote covering dig, cartage and cleanup.
Concord is a Federation-and-brick suburb on shale near the Parramatta River, basement, pool and knock-down work. The regular jobs here are basement digs, underpinning and pool digs. Services located first, sites left level and clean.
Get a free quoteNo obligation, free site quote.
Got it, thanks. We'll be in touch to arrange your site assessment and clear quote.
From a knock-down rebuild to a new estate pad, each service has its own page with the detail.
Concord sits about 11 kilometres west of the city. Locals place it by Concord shops, Concord Hospital, Majors Bay and Brays Bay. It's ringed by Concord West, North Strathfield, Mortlake, Strathfield and Burwood. What's changing: basement digs and underpinning under terraces, and granny flats and rear pools on the small lots.
Most of Concord is victorian and Federation terraces and semis, with heritage conservation areas throughout, over by Concord shops. Near Concord shops, duplex and unit sites cluster near the centres. On a Concord block that usually means basement digs, underpinning and pool digs.
Around Concord shops, Concord is on Wianamatta shale over clay toward the Parramatta River. Around Concord Hospital, Concord is flat enough that the drainage fall is built into the pad and the trenches rather than left to the ground. Around North Strathfield, the clay is reactive, so fill goes in in compacted layers.
In City of Canada Bay, Concord around Concord shops sits under heritage and tree protection controls, so the dig follows the approved plans. Access to Concord is off Concord Road or Majors Bay Road; it's tight-access through the old grid, near Concord West.
Every job follows the same sequence, whether it's a single trench or a full site cut.
A trench can be a day, a basement can be weeks. Dates come with the quote, not after.
Concord and the streets around it, from the older estates to the new blocks.
From the older streets to the newer blocks, Concord and the suburbs around it. If you're anywhere in the Concord area, we can get to you.
See the whole Inner West →It depends on the volume of material, the ground (wianamatta shale over clay toward the parramatta river), access for the machine and how far spoil has to be carted. Every job gets a written quote after a site look, with the dig, cartage and cleanup spelled out, so you know what’s included before anything starts.
Usually, if the excavation is part of a build. Cut and fill beyond set limits, work near boundaries and anything on a lot with a flood, bushfire or heritage overlay needs approval as part of the DA or CDC. We work to the approved plans; check with your certifier before the dig is booked.
A trench, pool dig or single pad is a day or two; a knock-down site cut or a basement runs longer and depends on volume, ground and weather. Dates come with the quote, not after.
Not usually in the first metre on the flat streets. Wianamatta shale over clay toward the Parramatta River. Shale under clay is ripped rather than broken, and old fill is the more common surprise than rock.
Yes, and it’s one of the most common Inner West jobs. The house is supported to the engineer’s underpinning design, the ground under it is dug in stages through the front or rear, and rock is sawn at the party walls so the neighbours’ footings stay put. Spoil goes out by conveyor.
Through the house on boards with the floor protected, or over the back fence by crane. Spoil comes out the same way or by conveyor into a skip in the lane. Slower than a side gate and priced for it, but it’s how most Inner West yards get dug.
Conditions on the approval, usually about keeping the front of the house, protecting the neighbours’ walls, and sometimes an archaeologist watching the dig on the oldest streets. Haberfield and the older parts of Balmain, Glebe and Marrickville are the strictest. We dig to what’s approved.
Reactive clay. It swells in wet winters and shrinks in dry summers, and anything poured on loose or uncompacted fill moves with it. A pad cut and filled in compacted layers to the engineer’s spec is what stops the new slab doing the same thing.
Tell us about the job. We'll look at the site before quoting, so you know what's included before anything starts.
Request received. We'll be in touch to arrange your site assessment and clear quote.